On average I end up cutting around 1.5'-3' off of the bottoms of logs to remove doty pith. These cut-offs become bolts, which are then riven(rived? rove?) with a froe and mallet to become shakes for roofing or siding. In the old days, they would have went through one more process of being smoothed and shaved to thickness and and possibly tapered with a draw-knife on a shaving-horse. Ideally all the shakes would be vertically grained, although all of mine are not. I purchased my froe for $8 at an antique store, and replaced pine handle with a persimmon sapling. I plan to make a bigger froe from an old leaf-spring sometime. Curved froes were used in the past to make staves for casks (barrels and such). It is a very primitive and effective tool, until you hit a knot. I am on my 4th mallet. The first being made of hickory, next was cherry, then persimmon, all of limbs or saplings. I am now using a piece of what I think is acacia (thorn tree), which has been the longest lasting. The pictures somewhat show the process of making shakes. I first split the bolt with a wedge (not shown), then knocked off the sapwood with the froe. The bolt is oriented upside down (tree top towards ground) for the whole process, as it splits easier for juniper in this manner. After spacing the froe from the edge it is hammer down flue with wood. The handle is then levered against the bolt to seperate the shake from bolt, and worked down and levered again, until the shake plops off. The shake can then be squared up if desired by using the froe again to slice through wood.
Thursday, February 26, 2009
Riving Shakes
On average I end up cutting around 1.5'-3' off of the bottoms of logs to remove doty pith. These cut-offs become bolts, which are then riven(rived? rove?) with a froe and mallet to become shakes for roofing or siding. In the old days, they would have went through one more process of being smoothed and shaved to thickness and and possibly tapered with a draw-knife on a shaving-horse. Ideally all the shakes would be vertically grained, although all of mine are not. I purchased my froe for $8 at an antique store, and replaced pine handle with a persimmon sapling. I plan to make a bigger froe from an old leaf-spring sometime. Curved froes were used in the past to make staves for casks (barrels and such). It is a very primitive and effective tool, until you hit a knot. I am on my 4th mallet. The first being made of hickory, next was cherry, then persimmon, all of limbs or saplings. I am now using a piece of what I think is acacia (thorn tree), which has been the longest lasting. The pictures somewhat show the process of making shakes. I first split the bolt with a wedge (not shown), then knocked off the sapwood with the froe. The bolt is oriented upside down (tree top towards ground) for the whole process, as it splits easier for juniper in this manner. After spacing the froe from the edge it is hammer down flue with wood. The handle is then levered against the bolt to seperate the shake from bolt, and worked down and levered again, until the shake plops off. The shake can then be squared up if desired by using the froe again to slice through wood.
Wednesday, February 18, 2009
Toolbox for Moulding Planes
I made a new toolbox for my Japanese moulding planes tonight. I still have to build a couple more toolboxes, luckily I have no shortage of lumber. I used juniper for the sides and bottom, and a couple of scraps of black walnut for the lid. It was built to match the length and width dimensions of my saw box. Dimensions are 36"L x 10.25"W x 4.75 and is finished with linseed oil.
Tuesday, February 17, 2009
Workshop Beginnings in SketchUp
This is my first attempt to draw 3D with SketchUp. It is not complete nor accurate at this point. I need to add rafters, extend the beams for barge rafters, and adjust my dimensions. I want when completed a shop around 16'x32'. Being a hillbilly, I have no choice but dirt floor (concrete is roughly $100yd here now). I will either set the post on poured concrete piers or flat out sink them in the ground. The walls will be wrapped in board and batten siding from the 1x's I have been pulling while milling posts.

Subscribe to:
Posts (Atom)
